nail making machine – Wire Nail Making Machine

The machine is designed to produce high quality nails, with reasonable price.

We are proud to say that we have researched a better design and have manufactured a machine to produce high quality nails for you. Our mission is to provide high-quality steel wire, alloy parts and electrical components, advanced processing equipment and strict quality control. We offer long-term technical support and after-sales service. With our reasonable price, you can enjoy the cost-effective nail making machine.

We can make all kinds of nails in different sizes and shapes, like concrete nail, flat nail, roofing nail and so on.

Nails are used for holding pieces of wood or material together. There are many different types of nails, as well as fastening machines that can be utilized. One type of fastener is the roofing nail. Roofing nails are used to fasten shingles, asphalt, slate and other roofing materials to a roof’s deck. This nail has a large head and is made from steel or aluminum in order to prevent corrosion from the elements. The shank of the roofing nail can be found in two different styles: smooth or spiral wound.

Flat head nails, also known as finish nails, have flat heads that allow them to sit flush with an object’s surface when hammered into it. These types of nails are used to hold together two pieces of wood; they are also used in carpentry and moldings because they do not protrude through the wood’s surface like other types of nails do.

The concrete nail is a type of nail that has been hardened by heat treatment so that it will not break when nailing into concrete or cinder blocks; this type makes driving easier and gives you a more secure hold in hard surfaces like bricks and concrete walls (which would otherwise shatter most standard wood-working nails).

Mainly parameters of nail making machines are as follows:

You should check that the equipment is complete and there is no missing part before starting the equipment, and then start to operate the equipment according to the order of operation.
When loading material into nail making machine, it must be added step by step according to the speed limit of feeder. If too much material is added at one time, abnormal noise will occur during operation, which will affect work efficiency and even damage parts.
After use of nail making machine should be in strict accordance with the specified load apply power supply voltage at random to prevent burn equipment parts due to overcurrent caused by excessive voltage.
Regular cleaning of nail making machine must be done every day after work, not only for easy operation next time but also for good health condition of equipment itself!

Raw material: steel wire rod Q195 or Q235 diameter 5.5mm in coil

Wire rod specification and expected wire diameter range:

Raw material: steel wire rod Q195 diameter 5.5mm in coil, the finished nail size is about 2.8-3.2mm;

Raw material: steel wire rod Q195 diameter 6.5mm in coil, the finished nail size is about 3-4mm;

Raw material: steel wire rod Q195 diameter 8mm in coil, the finished nail size is about 4-6mm;

The raw material of each product can be selected according to customer requirements, but the cost will be different, and you need to bear the transportation costs for materials required by customers

Wire diameter for making nails: normally 1.8-4mm, also can be made according to customers’requirement.

The diameter of wire for making nails can be 1.8-4mm in general, but we can also make according to your requirements.

Nail length: 20-200mm,also can be made according to customers’requirement.

Oops! Click Regenerate Content below to try generating this section again.

Production speed: 200-500pcs/min for cut wire nail making machine; 200-600pcs/min for common wire nail making machine; 200-800pcs/min for high speed wire nail making machine.

The production speed of machine depends on the type and quality of the machine you buy. For cut wire nail making machine, the price is cheaper and its production speed is also lower than common one and high speed one. The following table shows you clear data about production capacity:

common type:200-600pcs/min

high speed type:200-800pcs/min

Weight of the machine from 2 Ton to 3 Ton depends on different models.

The ‘weight’ of the machine is between 2 ton to 3 ton depends on different models. For example, the weight of small model like HR-65, MH-75 series is about 2 Ton and for big model like HRB-80G series, it can be as large as 3 Ton. It is because the size of small model is much smaller than middle and big models. Actually, it could be more accurate that we should say “its packing box” rather than just “the weight” to calculate its volume for freight charge because what included in a packing box varies from one type to another. Also, there are some other machines except nail making machines, such as wire straightening and cutting machines, wire drawing machines and so on. So all these kinds should also be considered when calculating its actual volume and weight of all products put together by LCL (less than container load).

This type is hot sale in Africa market.

You can find them in India, Europe, the US, South Africa, Australia and Asia. We’re a leading supplier of wire nail making machines from 1 to 6 inch nails.